#Elexa consumer products level mount install#
#Elexa consumer products level mount full#
#Elexa consumer products level mount tv#

Attaching Mounting Arms to a TV with Recessed or Curved Backįlat Panel TVs with a recessed back panel will require a longer bolt.

Tighten bolts firmly with a Phillips screwdriver. Thread the proper bolt through the appropriate Lock Washer, and Flat Washer, the adapter Arm and into the TV. Laying the television down on the glass may cause permanent damage.įlat Panel TVs with a flat back panel will require a shorter bolt. NOTE: NEVER LAY YOUR TELEVISION FACE DOWN ON ITS GLASS.

Attaching Mounting Arms to a TV with a Flat Back.

The multiple hole pattern on the Adapter Arms make it easy to adjust to fit your unique television.Īttach the Adapter arms to the mount as shown.Īfter securing the Adapter arms to the mount, The arms will be attached to the TV using the appropriate screws, washers, and lockwashers as described in Steps 6 and 7. It is recommended to measure the distance between the mounting holes on the back of your TV prior to attaching the Adapter Arms. If you need to use the Adapter Arms, you must use all Adapter Arms in order for the Mount to properly hold your TV. The included adapter arms can be used for Flat Panel monitors with bolt patterns larger than 100 mm x 100 mm. You will not use all of the hardware included. If you feel resistance, remove the bolt immediately and try another size! Next determine the correct length of the required bolt as described in the steps 6 and 7. Thread the bolts carefully into your Flat Panel by hand to determine which provided mount hardware (correct diameter) is appropriate for installation. Select the bolts which most resemble the holes in the back of your Flat Panel.

Selecting the Appropriate Hardware for your Flat Panel.

You will need 2 screws and anchors for the Small mounts and 4 screws and anchors for the Medium mount. Please be sure to use all wall screws and anchors that are included in the package. Insert the anchors into the holes and set them flush to the wall by tapping them in with a hammer. Drill into the wall at least as deep as the screw is long (2.5 inches). Drill holes for the concrete anchors using an electric drill with a masonry bit (15/32 inches or 12 mm). Mark the two or four holes you will be using for concrete anchors.

Attaching Wall Plate to Concrete or Brick Wall.

You will need 2 screws for the Small mounts and 4 screws for the Medium mount.

Please be sure to use all wall screws that are included in the package. The integrated Bubble level should be used to ensure a straight installation. Mark the two or four holes you will be using.

#Elexa consumer products level mount install#

Place the Wall Plate at the height you want to install the Flat Panel Wall Mount. It is recommended that the center of the stud be used and that a nail be used to verify that a stud has been located.

#Elexa consumer products level mount full#

Make sure all screws and bolts are tightened before allowing Wall Mount to bear the full weight of the Flat Panel Display. DO NOT MOUNT ONLY TO DRYWALL.īefore installing, check to make sure all parts of the mount are included. THE MOUNT MUST BE ATTACHED TO WOOD STUDS OR TO PROPERLY INSTALLED ANCHORS IN CONCRETE. It is the responsibility of the installer to verify that the mount is anchored properly to the wall. Installer must make sure the Flat Panel Wall Mount is properly and securely attached and that appropriate fasteners are used. Please also visit our Web Site at for assistance. Our trained Customer Service Department is open 24 hours a day, 7 days a week, every day of the year and is prepared to assist you in both English and Spanish.

Level Mount Small and Medium Flat Panel TV Mounts InstructionsĭO NOT RETURN THIS PRODUCT TO THE STORE OR WEB SITE YOU PURCHASED FROM! IF YOU BELIEVE THIS MOUNT IS DEFECTIVE, HAS MISSING OR BROKEN PARTS, OR IF YOU ARE HAVING DIFFICULTY INSTALLING THIS MOUNT TO YOUR WALL OR FITTING YOUR TV, PLEASE CONTACT OUR COMPANY, LEVEL MOUNT, DIRECTLY.ĭial 1 8 or email us at any time of the day or night for a quick and efficient solution to your problem. Level Mount Small and Medium Flat Panel TV Mounts 180° Zoom The Full motion feature adds the ability to extend the TV 6.5” to 14” from the wall depending on model.ħ. The Pan/Tilt models have the flexibility of being mounted in a fixed position while allowing up to 15° of tilt and 30° pan to position your screen for optimal viewing. The Fixed position mounts offer a low-profile design. Level Mount offers a full line of small and medium mounts to accommodate most TV wall mounting needs.

Low Profile Fixed, Tilt or Full Motion Capability:.We also apply a thick lead-free powder coating to prevent rust and corrosion. This prevents sagging, bending, warping, breaking over the life of the mount. This particular line is constructed using 2.5mm steel (the thickest in the industry). Level Mount Small and Medium Flat Panel TV Mounts Features See Flash demo for product images and multimedia.